![]() Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS. LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis. LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-ÄevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not SupportedÄevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl: ASPM Disabled RCB 64 bytes Disabled- CommClk-Ä®xtSynch- ClockPM- AutWidDis- BWInt- AutBWInt. LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64usĬlockPM- Surprise- LLActRep- BwNot- ASPMOptComp. ![]() MaxPayload 128 bytes, MaxReadReq 512 bytesÄevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend. RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop. ![]() Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-Ĭapabilities: MSI: Enable- Count=1/4 Maskable+ 64bit+Ĭapabilities: Express (v2) Endpoint, MSI 00ÄevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64usÄ®xtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000WÄevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported. Expansion ROM at e0000000 Ĭapabilities: Power Management version 2įlags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Region 0: Memory at e1000000 (64-bit, non-prefetchable) Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Lite-On Communications Inc Device 6631Ĭontrol: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx. It does not use any kernel module, as I can see in lspci -vvv: 01:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) It has wireless adapter that shows as Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) in lspci. Both Broadcom adapters works as expected, but I'm unable to get the Gigabyte WiFi to work. I inserted Gigabyte GC-WB300D in a PCIe Ã16 slot (just because I want it as near to the CPU as possible and not to slow down anything on south bridge like those two LAN adapters). The board (Gigabyte 955X Royal) has two Broadcom LAN adapters, one I want to use as WAN, second one as LAN. I'm trying to setup OpenWRT (latest 18.06.2) on an older hardware with Pentium 4 EE (don't ask why and please do not concern about power requirements).
0 Comments
Leave a Reply. |